New from HPS LLC
New spray adhesive for our rub-on decal paper..
Rub-On Spray Decal Adhesive.
- the New Aerosol Rub-on Decal Paper (media) can be used to make clear permanent production decals. the Rub-On decals will adhere to almost any substrate including; most types of plastic, metal, glass, marble, slate, unpainted wood, any painted substrate, great on most types of textured interior walls (nock-down finish), ceramic bisque, porcelain bisque, any glazed or unglazed fired ceramic or porcelain, glass, most type of wax candles, and fiberglass.
- Why use rub-on inkjet decal instead of self adhesive clear vinyl or water-slide decal?
- the rub-on decal media offers certain advantages over waterslide decal paper and self-adhesive inkjet vinyl. Rub-on decals provide greater water resistance than water-slide decals, not to mention clear inkjet vinyl, the rub-on decals are also thinner than vinyl and less prone to mechanical damage that may occur by the handling and use. the rub-on decals are also great for making permanent thin decals that almost look like they are printed on the substrate of the item they are used on. Water-slide decals are ideal for decorative items and hobby arts & craft creations whereas the rub-on transfer is a better choice for productions items. Rub-on decals will stick well to almost any substrate. Papilio Rub-on decals will accept almost any type of clear top coating. the Papilio rub-on decal media has been tested with and shows good compatibility with the following clear top coats; Oil Enamel, Acrylic, Epoxy, and two part Urethane.
- You must use Rub-On Decal Tack from HPS.
- Or similar product to be able to use our media.
-
Rub on decal paper.
1) Copy/Print on to the glossy side of the media.
2) Apply a thin coat of the Papilio Rub On Decal Tack. (If you are using Transfer Adhesive the follow the instructions that come with the transfer adhesive film.) Let the rub on decal tack dry for few hours, or over night. A second coat should NOT be applied.
Applying the decal.
1) Cut out the image with scissors while holding the paper at a constant 90 degree to prevent the media from sticking.
2) Apply the decal face down onto the substrate to be decorated.
3) Apply pressure to the back side of the paper using a solid object, such as a pen or pencil, working in a circular motion.
4) Use your fingers or a sharp object to lift off and discard the paper media. the artwork (the decal) will remain on the substrate.
For additional durability the Papilio Rub On Decal may be cover coated with various types of solvent based cover coats: epoxy, urethane, oil enamel, acrylic, etc.
this decal paper can also be used on various types of substrates: wood, marble, slate, glass, rock, different types of plastic, metal, most painted substrates, fiber glass, cardboard, etc.
DO NOT cut out the decal first and then apply the rub on decal tack as the edges of the paper will absorb the liquid making it difficult transfer the decal later.
1) Copy/Print on to the White Paper
2) Spray the decal using clear acrylic spray. Follow instructions on spray can.
If you are using our clear decal fixative then Let the first coat (the puddle) sit on the decal for about 20 seconds and gently move the puddle around on the decal the first few seconds then wait. then without applying any pressure on the decal use the foam pad to move the excess fluid off and over the edge of the paper on to a piece of cardboard and discard, leaving a thick and even coating on the image. Let dry for at least 8 hours or over night. Second coat may not be needed at all.
Applying the decal.
Cut out the image with scissors. Dip in warm water (not hot). the paper will roll up and then straighten out again.
When the film starts to loosen from the paper, place the paper on the substrate to be decorated, and slide the paper from under the decal.
Work out air bubbles with decal squeegee and let dry. It is important to remove all water and air.
Note: In some cases white clouds may appear in the clear film (may be slightly opaque) However the decal will turn completely clear over the period of 24 to 48 hours.
DO NOT cut out the decal first and then apply the solution as the edges of the paper will absorb the liquid making it impossible later to slide the decal off the paper.
Printing and Application Instructions
- 8 8:00 am to 4:30 pm central time.
- For other "How to" questions please read our FAQ.
Disclaimer: the user of our media must determine the suitability of each product before beginning production, using his equipment and method of application. the Sellers and Manufactures maximum obligation shall be to replace paper/film that has been found to be defective. Neither the manufacturer nor the seller shall be held liable for any injury, direct or consequential, arising out of the use of, or inability to use our paper or film.